JHG05 Two-Tone Heated Ski Gloves

J ONE JHG05 two-tone heated ski gloves pair a goat-skin palm with a light grey plain weave back panel for brands and distributors, with heating across all five fingers and a three-level controller.

Two-Tone Ski Glove Platform for Brand and Distributor Programs

JHG05 is a heated ski glove built around a material split rather than a single shell: goat skin on the palm and fingers, and a plain weave three-layer composite on the back of the hand. The composite panel carries the lighter grey tone that gives the model its two-tone face, and it is the reason the glove weighs less than an all-leather build of the same cuff length. Heating runs through all five fingers and the back of the hand on a 7.4 V system with a three-level button. Shell materials, panel colour, heating layout, controller, cuff hardware, sizing, logo and packaging are all set per project.

Customization Scope

The palm and fingertips are goat skin as standard, with sheep skin or cowhide available where a softer hand feel or a heavier gauge is needed. The back panel can stay on the composite, move to leather for a full-skin build, or change to a different composite weight. Panel colour is a specification item, which is why the sample is black with a light grey panel rather than a fixed colourway. Heating can be extended to the palm or reduced to the back of the hand only. Controller interface, cuff closure, lining weight, insulation, logo method and retail packaging are open to specification.

Heating System and Controller

The standard build uses a 7.4 V system drawing 7.5 W per glove, with elements running through all five fingers and across the back of the hand. A single button set into the gauntlet cycles three levels, and a colour ring shows the active setting at a glance. Temperature bands and runtime are stated below for the sample build; both shift when element layout, pack capacity or insulation is changed, so the final figures are confirmed at sample stage rather than assumed from the catalogue.

Palm, Back Panel and Insulation

The palm is goat skin with a cushion pad bonded under the wear zone, so grip pressure is spread rather than concentrated on one seam. Fingertips are conductive goat skin, which is what allows the glove to be used on a capacitive screen without taking it off. The back of the hand is a plain weave three-layer composite: an outer face fabric, a functional film, and an inner layer, which is what gives the panel its water resistance without leather weight. Behind the shell sits a velvet fleece lining over warming cotton. Panel weight, film specification and lining weight are all specification items.

Cuff, Retention and Gauntlet Fit

The cuff is an extended gauntlet that closes over a jacket sleeve. Retention is a webbing buckle across the wrist plus an elastic drawcord at the cuff opening, and a waterproof zip pocket on the side of the gauntlet takes a pass, a key or a spare pack. The red pull tab on the centre fingertip is a fixed part of the pattern; it is not removable and its colour does not change per order. Gauntlet length, buckle type and pocket placement are specification items.

Battery Pack

Two 7.4 V 3200 mAh packs are supplied as standard, one per glove, charged through an 8.4 V 1.5 A dual charger. Packs sit in the zip pocket inside the gauntlet, which keeps the weight behind the wrist instead of on the back of the hand, and the waterproof zip keeps snow out of the pocket. Capacity, pack shape and pocket position can be changed for programmes that need a longer runtime or a slimmer cuff.

Sizing and Fit Development

The base pattern runs S to 2XL. For private-label work we develop against the brand’s own size chart rather than forcing a stock grading: palm circumference, palm length and finger length are measured on the brand’s target fit model, and a fit sample is signed off before production tooling is set. Width across the knuckles and thumb length are the two dimensions that most often need adjustment between markets, and a cuff that has to sit over a bulky jacket sleeve is checked on the same fit sample.

Compliance and Documentation

The glove and its electrical parts are covered by CE, RoHS, FCC, ETL, UN38.3 and MSDS documentation. Certificates are issued against the specific configuration ordered, so the file references the battery and charger actually used rather than a generic listing. Copies are available on request during evaluation, and the certificate set is confirmed before mass production starts.

Sampling and Order Flow

A programme normally starts with a specification sheet, then a sample pair built to that sheet, then a signed sample before bulk. Minimum order quantity is assessed per project rather than fixed at a single number, because leather sourcing, panel material and packaging all move the economic batch size. Lead time is quoted against the confirmed sample and the materials selected.

Specifications

Specification Details
Model JHG05
Type Heated Ski Gloves, OEM/ODM Platform
Color Black with Light Grey Panel (Custom Colourways Available)
Palm Goat Skin with Cushion Pad
Fingertips Conductive Goat Skin
Back of Hand Plain Weave Three-Layer Composite
Cuff Extended Gauntlet with Webbing Buckle and Drawcord
Pocket Waterproof Zip Pocket on Gauntlet
Heating Zone Back of Hand and All Five Fingers
Heating Element 7.4V, 7.5W per Glove
Controller Single Button, Three Levels with Colour Indicator
Temp. Settings 3 Levels (Green / Blue / Red)
Level 1 (Green) 40-45°C (104-113°F) / 8.5-9 Hours
Level 2 (Blue) 50-55°C (122-131°F) / 4.5-5 Hours
Level 3 (Red) 60-65°C (140-149°F) / 2-2.5 Hours
Battery 7.4V 3200mAh, Two Packs Included
Charger 8.4V 1.5A Dual Charger
Sizes S / M / L / XL / 2XL
Lining Velvet Fleece with Warming Cotton
Customization Palm Leather, Back Panel, Heating Zones, Controller, Logo, Sizing, Packaging
MOQ Flexible, Assessed per Project
Certification CE / RoHS / FCC / ETL / UN38.3 / MSDS

FAQ

Is the back of the hand leather?

No. The palm and fingertips are goat skin; the back of the hand is a plain weave three-layer composite. A full goat-skin back is available as a specification change.

Why is the back panel a different material?

The composite is lighter than leather at the same cuff length and gives the two-tone face. It also lets the panel take a colour that a leather dye lot cannot match exactly.

Can the panel colour be changed?

Yes. Panel colour is specified per order, and the sample shown is black with a light grey panel.

Does heating cover the fingers?

Yes. Elements run through all five fingers and across the back of the hand. Palm heating can be added as a specification option.

What is the minimum order?

MOQ is assessed per project. Leather selection, panel material and packaging all affect the batch size, so it is quoted against the confirmed specification.

Reviews

There are no reviews yet.

Be the first to review “JHG05 Two-Tone Heated Ski Gloves”

Your email address will not be published. Required fields are marked *