Leather Mitten Platform for Brand and Distributor Programs
JHG09 is a heated ski mitten rather than a glove: one shell over four fingers and a separate thumb compartment. That shape is where the warmth advantage comes from, because the fingers share one heated cavity instead of five separate ones, and the shell carries fewer seams to leak heat. Goat leather covers the palm and the back panels, with twill fabric between the leather sections and at the cuff where the shell has to stretch. A cushion pad is bonded under the palm wear zone. Heating runs on a 7.4 V system with a three-level button on the gauntlet. Leather, panel split, heating layout, controller, cuff hardware, sizing, logo and packaging are all set per project.
Customization Scope
Palm and back leather are goat skin as standard; sheep skin, cowhide or a heavier gauge can be specified where a softer hand feel or more abrasion resistance is needed. Mitten body length, thumb compartment shape and the balance between leather and twill panels are specification items, which is why the sample reads as mostly leather with fabric between the panels rather than a fixed pattern. Heating can be limited to the back of the mitten, extended to the palm side, or run as two separate circuits. Controller interface, cuff closure, lining weight, insulation, logo method and retail packaging are open to specification.
Heating System and Controller
The standard build uses a 7.4 V system drawing 7.5 W per mitten, with the element film running across the back of the mitten and into the thumb compartment. A single button set into the gauntlet cycles three levels, and an indicator ring on the same button shows the active setting. Temperature bands and runtime are listed in the specification table for the sample build; both move when element area, pack capacity or insulation is changed, so final figures are confirmed at sample stage rather than carried over from the catalogue.
Leather Shell, Cushion Pad and Lining
The palm is goat leather with a cushion pad bonded under the wear zone, so grip pressure on a pole or a ski edge is spread across the pad instead of loading a single seam. On the back, leather panels are separated by twill fabric, which is what lets the mitten flex along the knuckle line without the leather puckering. Light grey piping runs along the panel edges. Behind the shell sits a velvet fleece lining over warming cotton. Leather thickness, pad hardness, panel split and lining weight are specification items.
Cuff, Retention and Gauntlet Fit
The cuff is an extended gauntlet that closes over a jacket sleeve, held by a webbing buckle across the wrist and an elastic drawcord at the opening. A waterproof zip pocket on the side of the gauntlet takes a pass, a key or a spare pack. Gauntlet length, buckle type and pocket placement are specification items.
Battery Pack
Two 7.4 V 3000 mAh packs are supplied as standard, one per mitten, charged through an 8.4 V 1.5 A dual charger. Capacity is a specification item: 2200 mAh packs are available where a lighter cuff or a shorter run time is acceptable. The pack sits in the zip pocket inside the gauntlet, which keeps the weight behind the wrist rather than on the back of the hand, and the waterproof zip keeps snow out of the pocket. Capacity, pack shape and pocket position can be changed for programmes that need a longer runtime or a slimmer cuff.
Sizing and Fit Development
The base pattern runs S to 2XL. For private-label work we develop against the brand’s own size chart rather than forcing a stock grading: hand circumference, hand length and thumb length are measured on the target fit model, and a fit sample is signed off before production tooling is set. A mitten is less forgiving than a glove on thumb position, so the thumb compartment angle is checked on the same fit sample against the brand’s reference product.
Compliance and Documentation
The mitten and its electrical parts are covered by CE, RoHS, FCC, ETL, UN38.3 and MSDS documentation. Certificates are issued against the specific configuration ordered, so the file references the battery and charger actually used rather than a generic listing. Copies are available on request during evaluation, and the certificate set is confirmed before mass production starts.
Sampling and Order Flow
A programme normally starts with a specification sheet, then a sample pair built to that sheet, then a signed sample before bulk. Minimum order quantity is assessed per project rather than fixed at a single number, because leather sourcing, panel layout and packaging all move the economic batch size. Lead time is quoted against the confirmed sample and the materials selected.
Specifications
| Specification | Details |
|---|---|
| Model | JHG09 |
| Type | Heated Ski Mittens, OEM/ODM Platform |
| Color | Black (Custom Colourways Available) |
| Palm | Goat Leather with Cushion Pad |
| Shell | Goat Leather with Twill Fabric Panels |
| Fingertips | Conductive Goat Leather |
| Cuff | Extended Gauntlet with Webbing Buckle and Drawcord |
| Waterproof Zip Pocket on Gauntlet | |
| Heating Zone | Back of Mitten and Thumb Compartment |
| Heating Element | 7.4V, 7.5W per Mitten |
| Controller | Single Button, Three Levels with Indicator Ring |
| Temp. Settings | 3 Levels (High / Medium / Low) |
| Level 3 (High) | 65°C (149°F) / 2-3 Hours |
| Level 2 (Medium) | 50°C (122°F) / 3-4 Hours |
| Level 1 (Low) | 40°C (104°F) / 5-6 Hours |
| Battery | 7.4V 3000mAh, Two Packs Included (2200mAh Option) |
| Charger | 8.4V 1.5A Dual Charger |
| Sizes | S / M / L / XL / 2XL |
| Lining | Velvet Fleece with Warming Cotton |
| Customization | Leather, Panel Layout, Heating Zones, Controller, Battery Capacity, Logo, Sizing, Packaging |
| MOQ | Flexible, Assessed per Project |
| Certification | CE / RoHS / FCC / ETL / UN38.3 / MSDS |
FAQ
Why a mitten instead of a glove?
A mitten puts four fingers in one heated cavity, so the heat has less surface area to cover and no seams between fingers to leak through. It is the warmer shape at the same battery capacity, at the cost of fingering dexterity.
Is the whole mitten leather?
No. Goat leather covers the palm and the back panels; twill fabric sits between the panels and at the cuff where the shell has to stretch. A full-leather shell is available as a specification change.
Does the thumb heat as well?
Yes. The element film runs across the back of the mitten and into the thumb compartment.
Can the palm side be heated?
Yes. Palm-side elements can be added as a specification option, either as a single circuit with the back or as a separate circuit.
What is the minimum order?
MOQ is assessed per project. Leather selection, panel layout and packaging all affect the batch size, so it is quoted against the confirmed specification.
















Reviews
There are no reviews yet.